DIY Furniture Studio

Little Cement Low Table or Plant Stand with Chunky Legs

Every now and then I have a project that just doesn’t work out, at least not in time for the next time I want to post. This happened right before a recent Christmas-time trip to visit my sister and her family. In fact, two projects didn’t work well enough to put out there on the web. That left me in a bit of a bind, being away from home and not able to work on another project. Well the good news is, the break at Christmas gave me a chance to get a project gallery onto my blog, something I’ve wanted to do for a while. Check it out in the menu bar above.  Another thing I had time for during the break is starting a new community Pinterest board–Concrete and Cement Furniture/Decor/Garden Community Board.  I started it because I wanted a place for concrete/cement enthusiasts to have a place to gather and post.  Check it out and follow the board if you like it.  If you want to join as a contributor, type “ADD ME” on this pin https://www.pinterest.com/pin/500603314815473738/ (shown below).

DIY Furniture Studio Concrete and Cement Furniture/Decor/Garden Community Board.

I’ll then send you an invite to the board, and after you accept the invite you can add pins to the board.  You know who you are, and you need to join!

During the Christmas trip, I spent considerable time with paper and a pencil on airplanes.  I now have many furniture and decor ideas that need developing, and the procedures and details ferreted out–which for me usually takes some time and trial and error.  Okay, to make a long story short, I still needed a project to put up on the blog in the short term, so I wandered around the house looking at what I had and came up with an idea.  I call it a little cement low table with chunky legs, aka a cement plant stand with chunky legs.

The legs were cast-off candle holders that I had made previously to give as a gift to a friend, but the colors didn’t turn out how I intended. I used red and green/chartreuse paint in the cement mix when making them, wanting Christmas-themed candle holders. The colors, once mixed with the cement, ended up looking pink and yellow.  This can happen.  Instead of giving them to someone else, I decided to use the candle holders as legs.  I just needed to make a little cement table top to go with them.

Here is how I made my little low table (or plant stand).

Supplies:

About the Paint

The type of paint to use for coloring cement (and concrete) is latex paint.  Most interior wall paints are this type of paint.  Leftover paint and sample-size jars are ideal for this project because you don’t need much.  The paint tints the cement when added in the mixing process, giving a muted version of the color and sometimes an unexpected color!

Mixing and Pouring the Cement 

Cement with Latex Paint Recipe

Use the following general proportions per batch:

8 parts Quikrete anchoring cement or Cement All (dry) by volume
1 part water
1/2 to 1 part latex paint

Casting the Molds

First, coat the inside of your leg and table top molds with cooking spray oil.  Be sure to wear a dust mask and gloves when working with cement.

A rough estimate of how much dry cement needed to make a batch that will fill a mold is to start with 1 and a half volumes of the mold of cement.  So fill your mold with dry cement and put this in a mixing bowl, then fill your mold halfway with dry cement and put it in the mixing bowl. Note how much cement this is (by volume), and then determine how much water and paint to use according to the recipe above.  If you are using rocks like I did in the legs, use about 1 volume of cement instead of 1.5 to start. These are estimates to get you in the ballpark.

Once you have mixed a few batches, you might not need to measure anything. I usually just measure the cement, add a bit of paint, and add water until I get the consistency I want. I mix with a gloved hand, but you can use a spoon, stick, or similar.

First put anchoring cement and paint in a mixing bowl.  Next add water, mix, and adjust the batch to a pourable consistency, like a pourable pudding.  If you are not adding paint to the batch, you can add more water.

I used a mixing variation for the greenish-yellow part of the cement legs.  First, I made a pourable cement batch using chartreuse paint mixed in thoroughly.  Just before I poured it into the four leg molds, I put a bit of paint into the mixing bowl on top of the cement, dribbling the paint in circles on the surface.  Then I poured the cement into the four legs.  This technique gives the cement a bit of color variation.  I let the cement cure about an hour.

After this, I added white stones (from Dollar Tree) to the cup molds.  The stones add some texture or variety.  It is totally up to you if you add them or not.

I mixed another batch of colored cement, this time using red paint, and poured it over the stones in the mold.

For the table top, I wanted a round mold with fairly straight walls.  I ended up using a springform cake pan that I had sitting in the kitchen taking up valuable real estate.  I hadn’t used it in years.  It worked okay but next time I’m going to grease it up more, especially where the bottom meets the sides so that it releases easier.  You can use one of the springform pans, a plastic or aluminum disposable dish, a cardboard shipping container, or anything similar.  For the table top, I used navy and white paint to get a light blue cement.  I didn’t add any stones to the table top.

Assembly

After a day, I was ready to glue the legs to the table top.  To help position the four legs on the underside of the table top, I cut a small square of paper and centered it.  This made it easier to position the legs properly.

Once in place, I drew around each leg with a pencil to mark the location.

I used E6000 Industrial Strength Adhesive to attach the cement legs to the cement table top.

After another day, the glue was dry, and the table was ready to use. You might want to seal the table/stand. I used two different silane-type sealers on previous cement furniture and decor projects, and they both worked well: RainGuard and Behr Concrete & Masonry Protector and Waterproofer.

Until next time.  Thanks again for joining me!
Jen

 

Now Linking at these Parties!

To Grandma’s House We Go Wednesday DIY Link Party
Sincerely, Paula’s No Rules Weekend Blog Party
SHARE CRAFTS, DIY PROJECTS, TRANSFORMATIONS #252

 

Exit mobile version